Видео

@THEELECTRONICGUY bro at the end u didn't show the full connection is the bulb taking current separately or is it taking it from Arduino

Code and Circuit Diagram: etechnophiles.com/step-counter-using-esp32/

My own servo is not working with my receiver any possible solution please

I solder a 3.7v 850mah lipo to the board and planned to use the 5v pin for npn motor control, but the motor didn't start up. I haven't tested with a volt meter but i assume there is voltage there. When connected to usb power supply, the motor starts up to verify the circuit is correct. I tried two lipo 3.7v 850mah in parallel to increase Ampacity. Still, the motor did not start up. Will i burn the board up if i connect two lipo 3.7v batteries in series to double the voltage?

What if the terminal for positive is broken solution pls cause phone cant switch on

Mercury is poisonous. Imagine dropping the sensor and the mercury is everywhere. Yeah this is a splash potion to instant heaven 💀

oh is that mercury sensor a tilt switch? cool project tho!

Off- on and close program.... Please share code

This video is now out of date as Digistump no longer have a website, so you cannot add the URL under preferences.

Can u make a artificial horizon

Can we do this for speed ( km/hr)

How to make servo move back and forth without turning the potentiometer?

This display name ?

Man where's the code

Where to buy?

Thankyou for quick recap of diode concepts

This will not work if you move the vehicle to a new position. It will still follow the old path that is in it s memory. How about using a high precision GPS module

Great info !

love you!

tis was so easy i cannot tank you eno

Will this car work with 2 9V Zinc carbon cell?

Description??????

Did you use the Arduino support package from Matlab ? If I don't want to use the support package, is it possible to control an Arduino project using Matlab GUI ?

So i have to buy an entire board for every new project? It’s a pity! 😢

Teşekkür. Basitmiş.

IT DIDNT WORK, I CHANGED EVERY COMPONENTS AND IT STILL DIDNT WORK

wow follow back

Thx you helped me a lot!!!

How many volts did the source enter?

Excellent video....Is it a standard that it takes 5 RC to fully charge the capacitor (irrespective of R,C and EMF)? Thanks.

Lagta he Is video ka description kisi aur ne likha hoga.. isliye ye code ko comment me pin karna bhul gaye hai😅

Nice project! Could you please let us know that this can ditect a pulse around 10MHZ. Thank you

hello i am using windows 11 laptop and i installaed all drivers of digispark but on arduino ide the code is not being uploaded to my attiny85 digispark. but the leds of attiny 85 are working but i can not upload the code to it. i cannot even update the drivers, if i try to update them there is no update button there are only install and delete buttos so what should i do please help me

Digistump avr not installing can someone help please

Jumper wire male to female?

thx

Fantastic presentation! Keep it up!

Download the program from here: www.etechnophiles.com/using-adxl345-with-esp32/

Code and Circuit Diagram: www.etechnophiles.com/wifi-strength-checker-using-esp32/

Download the program from here: www.etechnophiles.com/national-flag-on-tft-display-using-arduino/

Coooooooóooooooooooooode

Better use servo tester it has 3 different modes

MINES GOT SCK

code?

3 terminals can mean battery status indicator [BSI] or The the third terminal is a battery temperature indicator . but if it's got four terminals then it's a [Bsi ]Battery indicator and the a Battery temperature

Please share that Arduino library link

I want to replace my modem battery which standard old phone battery (square glat type) with 11650 type battery which has more capacity. Is it ok if i just connect + & - only? Is it still working if im not using BSI and BTemp? Thanks.

HI! Can you suggest simple potentiometar that works with this servo motor? For contionus slow or fast 360 spin?

Please remove music...

Hello need components to do project please send if you are available please pleasee